HomeQuizzes & Surveysfree Cisco 300-410 exam questions to pass 300-410 exam free Cisco 300-410 exam questions to pass 300-410 exam Welcome to your free Cisco 300-410 exam questions to pass 300-410 exam QUESTION 1 Refer to the exhibit. Which configuration configures a policy on R1 to forward any traffic that is sourced from the192.168.130.0/24 network to R2? A. Option A B. Option B C. Option C D. Option D None QUESTION 2 Refer to the following output:Router#show ip nhrp detail1.1.2/8 via 10.2.1.2, Tunnel1 created 00:00:12, expire 01:59:47 TypE. dynamic, Flags: authoritative unique natregistered used NBMA address:10.12.1.2What does the authoritative flag mean in regards to the NHRP information? A. It was obtained directly from the next-hop server. B. Data packets are process switches for this mapping entry. C. NHRP mapping is for networks that are local to this router. D. The mapping entry was created in response to an NHRP registration request. E. The NHRP mapping entry cannot be overwritten None QUESTION 3 Refer to the exhibit. A network engineer executes the show ipv6 ospf database command and is presented with theoutput that is shown. Which flooding scope is referenced in the link-state type? A. link-local B. area C. As (OSPF domain) D. reserved None QUESTION 4 What is the output of the following command: show ip vrf A. Show\\'s default RD values B. Displays IP routing table information associated with a VRF C. Show\\'s routing protocol information associated with a VRF D. Displays the ARP table (static and dynamic entries) in the specified VRF None QUESTION 5 Refer to the exhibit. An engineer is troubleshooting BGP on a device but discovers that the clock on the device does notcorrespond to the timestamp of the log entries. Which action ensures consistency between the two times? A. Configure the service timestamps log uptime command in global configuration mode. B. Configure the logging clock synchronize command in global configuration mode. C. Configure the service timestamps log datetime localtime command in global configuration mode. D. Make sure that the clock on the device is synchronized with an NTP server. None QUESTION 6 Refer to the exhibit. An IP SLA was configured on router R1 that allows the default route to be modified in the event thatFa0/0 loses reachability with the router R3 Fa0/0 interface. The route has changed to flow through router R2. Whichdebug command is used to troubleshoot this issue? A. debug ip flow B. debug ip sla error C. debug ip routing D. debug ip packet None QUESTION 7 Refer to the exhibit. Why is the remote NetFlow server failing to receive the NetFlow data? A. The flow exporter is configured but is not used. B. The flow monitor is applied in the wrong direction. C. The flow monitor is applied to the wrong interface. D. The destination of the flow exporter is not reachable. None QUESTION 8 Refer to the exhibit. After applying IPsec, the engineer observed that the DMVPN tunnel went down, and both spoke-tospoke and hub were not establishing. Which two actions resolve the issue? (Choose two.) A. Change the mode from mode tunnel to mode transport on R3. B. Remove the crypto isakmp key cisco address 10.1.1.1 on R2 and R3. C. Configure the crypto isakmp key cisco address 192.1.1.1 on R2 and R3. D. Configure the crypto isakmp key cisco address 0.0.0.0 on R2 and R3. E. Change the mode from mode transport to mode tunnel on R2. QUESTION 9 After some changes in the routing policy, it is noticed that the router in AS 45123 is being used as a transit AS router forseveral service provides. Which configuration ensures that the branch router in AS 45123 advertises only the localnetworks to all SP neighbors? A. Option A B. Option B C. Option C D. Option D None QUESTION 10 Refer to the exhibit. An engineer is monitoring reachability of the configured default routes to ISP1 and ISP2. The default route from ISP1 ispreferred if available. How is this issue resolved? A. Use the icmp-echo command to track both default routes B. Use the same AD for both default routes C. Start IP SLA by matching numbers for track and ip sla commands D. Start IP SLA by defining frequency and scheduling it None QUESTION 11 Refer to the exhibit. An IP SLA is configured to use the backup default route when the primary is down, but it is not working as desired.Which command fixes the issue? A. R1(config)# ip route 0.0.0.0.0.0.0.0.2.2.2.2 10 track 1 B. R1(config)# ip route 0.0.0.0.0.0.0.0.2.2.2.2 C. R1(config)#ip sla track 1 D. R1(config)# ip route 0.0.0.0.0.0.0.0.1.1.1.1 track 1 None QUESTION 12 Refer to the exhibit. Which interface configuration must be configured on the spoke A router to enable a dynamicDMVPN tunnel with the spoke B router? A. Option A B. Option B C. Option C D. Option D None QUESTION 13 Which is statement about IPv6 inspection is true? A. It teams and secures bindings for stateless autoconfiguration addresses in Layer 3 neighbor tables B. It learns and secures bindings for stateful autoconfiguration addresses in Layer 3 neighbor tables C. It teams and secures bindings for stateful autoconfiguration addresses in Layer 2 neighbor tables D. It team and secures binding for stateless autoconfiguration addresses in Layer 2 neighbor tables None Time's up
