Take the Cisco 350-401 exam. Tired of remembering dumps with hundreds of old questions with no answer to explain? Don’t worry, Pass4itSure has updated the latest version of the 350-401 dumps for you to help you learn easily.
Free sharing of free Cisco 350-401 exam questions and Cisco 350-401 dumps from Pass4itsure. Pass4itsure offers up-to-date Cisco 350-401 questions along with verified answers. It will be the key for an easy, successful 350-401 exam on at first try – https://www.pass4itsure.com/350-401.html authenticity and effectiveness Cisco 350-401 dumps download.
| Release time | Release time |
| Cisco 350-401 exam dumps [2020.12] | Cisco 350-401 exam dumps [2022.12] (latest version) |
New Updated [2022.12] Cisco 350-401 exam questions from Pass4itsure Cisco 350-401 PDF dumps! Welcome to download the newest Pass4itsure Cisco 350-401 PDF dumps:
Free Cisco 350-401 PDF download
[google drive] Latest Cisco 350-401 PDF
https://drive.google.com/file/d/1tkPwTavFjjXlt4gzLWBvpvUf9auk-Xlu/view?usp=share_link
2022 New updated Cisco 350-401 practice test free online 1-15
Welcome to your free Cisco 350-401 exam questions (latest version) to pass the 350-401 exam.
New Question 1:
Refer to the exhibit.
The EtherChannel between SW2 and SW3 is not operational which action resolves this issue?
A. Configure the channel-group mode on SW2 Gi0/0 and Gi0/1 to on.
B. Configure the channel-group mode on SW3 Gi0/0 and Gi0/1 to active.
C. Configure the mode on SW2 Gi0/0 to trunk.
D. Configure the mode on SW2 Gi0/1 to access.
Correct Answer: C
New Question 2:
What is the data policy in a Cisco SD-WAN deployment?
A. list of ordered statements that define node configurations and authentication used within the SDWAN overlay
B. Set of statements that defines how data is forwarded based on IP packet information and specific VPNs
C. detailed database mapping several kinds of addresses with their corresponding location
D. group of services tested to guarantee devices and links liveliness within the SD-WAN overlay
Correct Answer: B
New Question 3:
Refer to the exhibit. A network engineer must simplify the IPsec configuration by enabling IPsec over GRE using IPsec profiles. Which two configuration changes accomplish this? (Choose two).
A. Apply the crypto map to the tunnel interface and change the tunnel mode to tunnel mode ipsec ipv4.
B. Create an IPsec profile, associate the transform-set. and apply the profile to the tunnel interface.
C. Remove the crypto map and modify the ACL to allow traffic between 10.10.0.0/24 to 10.20.0.0/24.
D. Remove all configuration related to crypto map from R1 and R2 and eliminate the ACL
E. Create an IPsec profile, associate the transform-set ACL. and apply the profile to the tunnel interface
Correct Answer: BD
New Question 4:
What is an advantage of utilizing data models in a multivendor environment?
A. lowering CPU load incurred to managed devices
B. improving communication security with binary encoded protocols
C. facilitating a unified approach to configuration and management
D. removing the distinction between configuration and runtime state data
Correct Answer: C
New Question 5:
Refer io me exhibit.
An engineer configures the trunk and proceeds to configure an ESPAN session to monitor VLANs10. 20. and 30.
Which command must be added to complete this configuration?
A. Device(config.mon.erspan.stc)# no filter vlan 30
B. Devic(config.mon.erspan.src-dst)# no vrf 1
C. Devic(config.mon.erspan.src-dst)# erspan id 6
D. Device(config.mon-erspan.Src-dst)# mtu 1460
Correct Answer: A
New Question 6:
Which command set configures RSPAN to capture outgoing traffic from VLAN 3 on interface GigabitEthernet 0/3 while ignoring other VLAN traffic on the same interface?
A. Option A
B. Option B
C. Option C
D. Option D
Correct Answer: B
New Question 7:
Refer to the exhibit. R1 is able to ping the R3 fa0/1 interface. Why do the extended pings fail?
A. The maximum packet size accepted by the command is 1476 bytes.
B. R3 is missing a return route to 10.99.69.0/30
C. R2 and R3 do not have an OSPF adjacency
D. The DF bit has been set
Correct Answer: D
If the DF bit is set, routers cannot fragment packets. From the output below, we learn that the maximum MTU of R2 is 1492 bytes while we sent ping with 1500 bytes.
Therefore these ICMP packets were dropped.
Note: Record option displays the address(es) of the hops (up to nine) the packet goes through.
New Question 8:
Which two security features are available when implementing NTP? (Choose two )
A. symmetric server passwords
B. dock offset authentication
C. broadcast association mode
D. encrypted authentication mechanism
E. access list-based restriction scheme
Correct Answer: DE
The time kept on a machine is a critical resource and it is strongly recommend that you use the security features of NTP to avoid the accidental or malicious setting of incorrect time. The two security features available are an access list-based restriction scheme and an encrypted authentication mechanism.
Reference: https://www.cisco.com/c/en/us/support/docs/availability/high-availability/19643-ntpm.html
New Question 9:
DRAG DROP
Drag and drop the descriptions from the left onto the routing protocol they describe on the right.
Select and Place:
Correct Answer:
New Question 10:
What is the result when an active route processor fails in a design that combines NSF with SSO?
A. An NSF-aware device immediately updates the standby route processor RIB without churning the network
B. The standby route processor temporarily forwards packets until route convergence is complete
C. An NSF-capable device immediately updates the standby route processor RIB without churning the network
D. The standby route processor immediately takes control and forwards packets along known routes
Correct Answer: D
Stateful Switchover Routers specifically designed for high availability include hardware redundancy, such as dual power supplies and route processors (RPs). An RP is responsible for learning the network topology and building the route table (RIB). An RP failure can trigger routing protocol adjacencies to reset, resulting in packet loss and network instability. During an RP failure, it may be more desirable to hide the failure and allow the router to continue forwarding packets using the previously programmed CEF table entries rather than temporarily drop packets while waiting for the secondary RP to reestablish the routing protocol adjacencies and rebuild the forwarding table.
Stateful switchover (SSO) is a redundancy feature that allows a Cisco router with two RPs to synchronize router configuration and control plane state information. The process of mirroring information between RPs is referred to as checkpointing. SSO-enabled routers always checkpoint line card operation and Layer 2 protocol states. During a switchover, the standby RP immediately takes control and prevents basic problems such as interface link flaps. However, Layer 3 packet forwarding is disrupted without additional configuration.
The RP switchover triggers a routing protocol adjacency flap that clears the route table. When the routing table is cleared, the CEF entries are purged, and traffic is no longer routed until the network topology is relearned and the forwarding table is reprogrammed. Enabling nonstop forwarding (NSF) or nonstop routing (NSR) high availability capabilities informs the router(s) to maintain the CEF entries for a short duration and continue forwarding packets through an RP failure until the control plane recovers.
New Question 11:
Which statements are used for error handling in Python?
A. try/catch
B. try/except
C. block/rescue
D. catch/release
Correct Answer: B
The words “try” and “except” are Python keywords and are used to catch exceptions.
For example:
try:
print 1/0
except ZeroDivisionError:
print \’Error! We cannot divide by zero!!!\’
New Question 12:
When does a stack master lose its role?
A. When the priority value of a stack member is changed to a higher value
B. when a switch with a higher priority is added to the stack
C. when the stack master is reset
D. when a stack member fails
Correct Answer: C
A stack master retains its role unless one of these events occurs:
1. The switch stack is reset.*
2. The stack master is removed from the switch stack.
3. The stack master is reset or powered off.
4. The stack master fails.
5. The switch stack membership is increased by adding powered-on standalone switches or switch stacks.*
In the events marked by an asterisk (*), the current stack master might be re-elected based on the listed factors. When you power on or reset an entire switch stack, some stack members might not participate in the stack master election. Stack members that are powered on within the same 20-second time frame participate in the stack master election and have a chance to become the stack master. Stack members that are powered on after the 20-second time frame do not participate in this initial election and become stack members. All stack members participate in re-elections.
For all powering considerations that affect stack-master elections, see the “Switch Installation” chapter in the hardware installation guide. The new stack master becomes available after a few seconds. In the meantime, the switch stack uses the forwarding tables in memory to minimize network disruption. The physical interfaces on the other available stack members are not affected during a new stack master election and reset. After a new stack master is elected and the previous stack master becomes available, the previous stack master does not resume its role as stack master. As described in the hardware installation guide, you can use the Master LED on the switch to see if the switch is the stack master.
New Question 13:
Refer to the exhibit.
An engineer attempts to configure a router on a stick to route packets between Clients, Servers, and
Printers; however, initial tests show that this configuration is not working.
Which command set resolves this issue?
A. Option A
B. Option B
C. Option C
D. Option D
Correct Answer: C
We must reconfigure the IP address after assigning or removing an interface to a VRF. Otherwise that interface does not have an IP address.
New Question 14:
Which PAgP mode combination prevents an Etherchannel from forming?
A. auto/auto
B. desirable/desirable
C. auto/desirable
D. desirable
Correct Answer: A
There are two PAgP modes:
Reference: https://www.omnisecu.com/cisco-certified-network-associate-ccna/etherchannel-pagp-andlacp-modes.php
New Question 15:
Refer to the exhibit. How does the router handle traffic after the CoPP policy is configured on the router?
A. Traffic coming to R1 that does not match access list SNMP is dropped.
B. Traffic coming to R1 that matches access list SNMP is policed.
C. Traffic passing through R1 that matches access list SNMP is policed.
D. Traffic generated by R1 that matches access list SNMP is policed.
Correct Answer: B
(After you finish, you may want to see other exams! :))
Reason for selection – Pass4itsure
- First-class exam experience!
- Very professional exam expert!
- Update test questions throughout the year!
- The most complete test questions and answers!
- The safest buying experience!
- Selflessly share exam practice questions and answers (partial) for free!
Conclusion:
In this article, I shared free resources: the latest Cisco 350-401 practice questions, and the latest Cisco 350-401 pdf dumps learning. For more questions, please visit https://www.pass4itsure.com/350-401.html Q&A: 866. Study hard and practice a lot. This will help you prepare for the Cisco 350-401 exam. good luck!
